comemso
Find the right system
Talk to application engineering
Start with the decisionApplications
Vehicle and charging station
EV TestingVehicle, EVCC and charging-release validation.EVSE TestingCharging-station development through field operation.InteroperabilityReal EV and EVSE in one synchronized test record.
Battery and advanced charging
BMS TestingCells, sensors, balancing and controlled faults.BMS + EVCC + OBCValidate the interaction of battery, charging controller and on-board charger.MCS TestingCommunication, signals, cooling and megawatt power.EV Charging EMCKeep charging communication observable under EMC stress.
Production and field
EVSE End-of-LineRepeatable acceptance and unit-level results.Commissioning & Field ServiceCommission, diagnose and verify installed chargers.Calibration & MetrologyTraceable energy verification at the charging point.
Start with the decisionProducts & PlatformsFind the right system
EVCA
EVCA PlatformCommunication, interoperability, high-power, MCS and EMC paths.EVCA ComOnlyFocused charging communication testing.EVCA Multi MobilePortable laboratory and field analysis.EVCA InteropAnalyse interoperability between a real EV and EVSE.EVCA FlexModular high-power testing and controlled faults.EVCA MCSMegawatt charging communication, low-level signals and system testing.
Easy Chester
Easy Chester PlatformEVSE production, commissioning, service and calibration.Easy Chester MicroAC EVSE installation testerEasy Chester UltimateAC and DC EVSE installation testerEasy Chester CalimeraAC and DC EVSE calibration systemEasy Chester EOL / EOL HPCEVSE end-of-line production tester
Battery, software and EMC
Battery Cell SimulatorBMS testing from compact bench to high-voltage HiL.comframeConfiguration, synchronized analysis and automation.EMC LinkOptical charging communication through the chamber boundary.
Start with the decisionSoftware Capabilities
Understand and challenge
Automated Standards AnalysisMeasured behaviour, normative context and highlighted deviations.Professional SimulationConfigure nominal, boundary and non-conform behaviour.Manipulating GatewayTest a live correction hypothesis between real partners.
Reproduce and automate
Charge PlaybackReproduce the charging partner for the DUT.Charge Cycle AutomationTurn saved configurations into repeatable campaigns.Conformance Test LibrariesVersioned executable standards-based test logic.
Software and integration
Capabilities HubConnect the capability model across EV, EVSE and BMS testing.EVCA Capability HubExplore the detailed EV charging capability stack.comframeThe shared test-intelligence environment.Integration & APIsREST, Python, CI/CD and laboratory orchestration.Protocol & Domain ModulesSelect released domain depth.
Start with the decisionStandards & Knowledge
Standards and test logic
Charging, Safety & EMCCharging behaviour, field safety, editions and test boundaries.Conformance Test LibrariesReleased executable test logic, verdicts and evidence.AFIR for EV ChargingRegulation, responsibility and verifiable evidence.
Methods and terminology
Knowledge CenterTechnical explanations, methods and application guidance.GlossaryStable charging and BMS test terminology.EVSE Calibration MethodsCompare controlled real load and reference measurement.Battery Cell SimulationCells, balancing, faults, precision and BMS HiL.
Documents and tools
Resources LibraryCurrent brochures, webinars, guides and checklists.Charger Uptime CalculatorEstimate downtime and field-service impact.EVSE Inspection GuidePractical commissioning and inspection workflow.BMS testing whitepaperTemperature, environment, simulation and test wiring.Technical newsletterChoose product updates and events relevant to your tests.
Start with the decisionCompany
Company
About comemsoEngineering purpose, history and operating companies.Development & manufacturingShort paths from development to system testingQuality & CertificationsManagement systems, validation and calibration evidence.Customer ProofNamed stories, endorsements and published configurations.SustainabilityEnvironmental management and measured progress.
People and network
Customer Care TeamDelivery, commissioning, training and support.Sales PartnersRegional commercial and service access.CareersWork on deep e-mobility testing.
Updates and contact
News & EventsProjects, releases, webinars and company updates.Request a technical demoDiscuss your test task with the comemso team.ContactSales, support and locations in one place.Legal documentsImprint, privacy, GTC, EULA and WEEE.
Event & webinar1–2 April 2025

Accelerating megawatt charging: comemso at the CharIN MCS Controller Testival Europe

comemso supported the CharIN MCS Controller Testival Europe in Barcelona as an official sponsor and early MCS test-system contributor.

Read articleAll news & events
Accelerating megawatt charging: comemso at the CharIN MCS Controller Testival Europe
Two DUT rolesVehicle or charging-system side
CommunicationMCS-specific messages and timing
Physical contextSignals, temperature and cooling
ScopePower integration depends on configuration
Original comemso publication

This dated article describes its original release context. Check the linked current product or application for available configurations and supported scope.

View original publication

comemso at CharIN MCS Controller Testival Europe 2025 – Supporting the Future of Megawatt Charging

We are proud to announce that comemso was an official sponsor of the CharIN MCS Controller Testival Europe 2025, which took place in Barcelona on April 1–2, 2025. As pioneers in EV and EVSE (electric vehicle supply equipment, or charging station) testing technologies, we are excited to support the early-stage development and testing of Megawatt Charging Systems (MCS) on communication level—a crucial step forward in the electrification of heavy-duty and high-power applications.

Why This Event Matters

The MCS Controller Testival gathered key industry players, engineers, and developers focused on testing and validating the new Megawatt Charging standard, aimed at trucks, buses, aircraft, marine, and mining applications.

As charging requirements grow, especially in sectors with ultra-high power needs, MCS is set to become a cornerstone of future e-mobility infrastructure. Events like this provide an essential space for early interoperability testing, feedback exchange, and joint progress toward globally accepted standards.

Our Commitment to MCS Development

At comemso, we believe in supporting innovation from the ground up. With our extensive expertise in e-mobility testing, we are actively contributing to the MCS ecosystem through:

  • Advanced EV and EVSE test systems with MCS-ready architecture
  • High-voltage (1500V), high-current support (up to 1000A) for real-world ev test conditions
  • Ongoing collaboration with standardization bodies and e-mobility industry partners

It was inspiring to witness the momentum, collaboration, and technical passion at the event—and to see how MCS is shaping the future of electrified transport.

We thank CharIN for organizing another valuable Testival and to Autel for hosting. Looking forward to supporting further milestones in the rollout of Megawatt Charging worldwide.

  • Want to know more about our role in MCS testing and how we can support your development?

Let’s connect!

Related reading

Continue through the archive.

Related entries retain the publication date and lead to the current technical route.

Event & webinar30 June 2026

Webinar archive: EVSE testing under control. IEC 61851-23 and beyond

A live webinar with UL Solutions connected IEC charging requirements with a practical DC-CCS testing approach.

Event & webinar21 April 2026

Webinar archive: Commissioning and inspection of charging stations

A practical live webinar for electricians and field teams focused on EVSE functionality, electrical safety and repeatable inspection methods.

Customer story2026

Customer success story: CMI brings charging-station calibration into the field

The Czech Metrology Institute integrated Easy Chester Calimera into a service vehicle for traceable AC and DC charging-station verification on site.

MCS test planning

Define communication, interface and power scope separately.

Specify the DUT (device under test) role, MCS interface, thermal context and separately configured source/load equipment.

Configure your test systemContact application engineering